Industrial Waste

Acid mine drainage (AMD) – characterized by high acidity and elevated sulfate and metal concentrations – represents a big environmental concern. Biological sulfate reduction has become an alternative to the classical physicochemical methods. In this study, domestic wastewater (DW) was tested as a cost-effective carbon-source for the remediation of AMD. Sediments from Tinto River, an extreme acidic environment with an elevated concentration of metals, were used as inoculum. Three anaerobic bioreactors with different microbial supports were fed with a 1:10 (v:v) mixture of synthetic AMD:DW. Around 50% of the organic matter present in the DW co-precipitated with the metals from the AMD previous to feeding the reactor. Therefore, the reactors had to be supplemented with an extra carbon-source (acetate) to achieve higher S elimination. Elevated removal efficiencies of chemical oxygen demand (COD) (>88%), sulfate (>75%), Fe (>85%) and other dissolved metals (>99% except for Mn...

The efficiency of ozone as a pre- and post-treatment to UASB treatment was investigated, followed by a study into UASB reactor performance with ozonated wastewater as substrate. Combinations of pre- and/or post-ozonation with UASB treatment gave better results than ozonation or UASB alone and COD reductions of 53.0-98.9% were achieved for treatment of canning and winery wastewaters. A UASB reactor was fed with pre-ozonated cannery wastewater for over 70 d. COD removal improved from between 58.8 and 64.4% to between 85.3 and 91.8% after pre-ozonated substrate feed commenced. Subsequent increases in organic loading rate (OLR) from 2.4 to 3.4 kgCOD m(-3) x d(-1) did not affect reactor performance. By including a final post-ozonation treatment to this UASB effluent a total COD reduction of 99.2% was achieved.

Lignocelluloses industrial waste flour of olive husk powder (LCF) was utilized as reinforcement in carboxylated nitrile butadiene rubber (XNBR)/Polyamide-12 (PA-12) thermoplastic elastomer composites. To improve the bonding quality between the LCF and the blend, the powder was chemically treated by two means, the former is the treatment with toulene-2–4-diisocyanate (TDIC), and the latter is mercerization with sodium hydroxide followed by neutralization with acetic acid. The untreated and chemically treated powders were analyzed with attenuated total reflectance infrared spectroscopy (ATR-IR). The morphology of the powders before and after treatment was studied with scanning electron microscopy (SEM). The LCF reinforced composites were prepared using computerized Haake internal mixer coupled with rheometer. The processing conditions were 178°C and rotor speed of 80- round per minute for 7 min. The melt mixing process was monitored by the torque-time plastograms of the Haake internal mixer. The development of the stock temperature during the mixing process was monitored using the rheometer of Hakke internal mixer. The structural changes of the XNBR/PA-12 composites were inspected by SEM and attenuated ATR-IR spectroscopy. The influence of the modified filler on the toughness and hardness of the prepared samples are reported. The resistance of the prepared composites to water and toluene swelling are evaluated as well.

The bagasse fly ash, an industrial solid waste of sugar industry, was used for the removal of cadmium and nickel from wastewater. As much as 90% removal of cadmium and nickel is possible in about 60 and 80 min, respectively, under the batch test conditions. Effect of various operating ...

Today, over-consumption, pollution and resource depletion threaten sustainability. Waste management policies frequently fail to reduce consumption, prevent pollution, conserve resources and foster sustainable products. However, waste policies are changing to focus on lifecycle impacts of products from the cradle to the grave by extending the responsibilities of stakeholders to post-consumer management. Product stewardship and extended producer responsibility are two policies in use, with radically different results when compared for one consumer product, refrigerators. North America has enacted product stewardship policies that fail to require producers to take physical or financial responsibility for recycling or for environmentally sound disposal, so that releases of ozone depleting substances routinely occur, which contribute to the expanding the ozone hole. Conversely, Europe's Waste Electrical and Electronic Equipment (WEEE) Directive requires extended producer responsibili...

In this work, a brewer’s yeast strain was used to remove heavy metals from a synthetic effluent. The solid–liquid separation process was carried out using the flocculation ability of the strain. The yeast strain was able to sediment in the presence of Cu2+, Ni2+, Zn2+, Cd2+ and Cr3+, which evidences that the flocculation can be used as a cheap and natural separation process for an enlarged range of industrial effluents. For a biomass concentration higher than 0.5 g/l, more than 95% of the cells were settled after 5 min; this fact shows that the auto-aggregation of yeast biomass is a rapid and efficient separation process. Cells inactivated at 45 °C maintain the sedimentation characteristics, while cells inactivated at 80 °C lose partially (40%) the flocculation.The passage of metal-loaded effluent through a series of sequential batches allowed, after the second batch, the reduction of the Ni2+concentration in solution for values below the legal limit of discharge of wastewater in natural waters (2 mg/l); this procedure corresponds to a removal of 91%. A subsequent batch had a marginal effect on Ni2+ removal (96%).Together, the results obtained suggest that the use of brewing flocculent biomass looks a promising alternative in the bioremediation of metal-loaded industrial effluents since the removal of the heavy metals and cell separation are simultaneously achieved.

The purpose of this study was to evaluate the production feasibility of triaxial whiteware using sand from cast iron moulds as a raw material instead of silica, and recycled glass in place of feldspar. Formulations were prepared using sand, glass waste, and white-firing clay such that only 50% of the composition was virgin material (clay). The ceramic bodies were formed by pressing and fired at different temperatures (between 1100 and 1300 degrees C). Specimens were characterized in terms of green density prior to firing; and their flexural strength, linear shrinkage, and water absorption were measured after firing. The microstructure was determined by scanning electron microscopy. Possible environmental impacts of this recycling process were also evaluated, through solubility and leaching tests, according to Brazilian standards. Gaseous emissions during the firing process were also analysed. The results showed that it is possible to produce triaxial ceramics by using such alternati...