CONSUMABLES 5.0
5.1 Supra Nylon Cords
5.3
5.4
5.0
5.5 Pens to colour Lenses and to touch-up Frames
5.6
5.7 Dyes for Lenses - Neutralizers
5.8 Soldering Consumables
LENSES
SUPRA NYLON CORDS AND PLASTIC STRIP 5.1
For supra frames assembly
CLEAR SUPRA NYLON CORDS
ROUND FIGURE “8”
Ref. 01232 Ø 0,4 mm
Ref. 01235 Ø 0,5 mm
Ref. 01233 Ø 0,6 mm
Ref. 01234 Ø 1,0 mm
5 m
FIGURE “T”
Ref. 01242
For metal frames
Ref. 01244
For metal and plastic frames
For metal and plastic frames 0,80
SILICONE GASKET FOR AIR-RIM
20 pcs. ROUND Ø 26,5 mm
Ref. 01263 Clear
Nylon Holding Plier 03465N to pull the nylon liner
Nylon Press-in Plier Ref. 03470N to press in the figure “8” liner
PLASTIC STRIP FOR SUPRA FRAMES ASSEMBLY
50 pcs.
Ref. 01249
Non-slip material
L = 70x5 mm
Mounting Hook Ref. 03480 to insert the liner into the groove of the lens
Ref. 01870
SUPRA KIT
Plastic strip Ref. 01249 to insert the liner into the groove of the lens
• Supra nylon cord Ø 0,5 mm clear Ref. 01235
• “Figure 8” Supra Liner clear. Ref. 01242
• “Figure T” Supra Liner clear. Ref. 01244
• Nylon Holding Plier Ref. 03465N
• Nylon Press-in Plier Ref. 03470N
• Mounting Hook Ref. 03480
Tray included, suitable for new LMS Cube.
LENS AND FLEX SIDES WASHERS 5.1
In nylon, acetate, silicone, adhesive and rubber
FLEXIBLE NYLON LENS WASHERS
Dip in acetone to soften and fix into plastic frame groove
SEMI-RIGID ACETATE LENS WASHERS
MEDIUM
MEDIUM Ref. 01255
SOFT SILICONE LENS WASHERS
MEDIUM Ref. 01260
4,5 m
In easy to use dispenser
• Adjustable with heat.
• Dip in acetone to soften and fix into plastic frame groove.
HYPO-TUBE CEMENT
Liquid lens liner suitable for: Eyerims - Rimless - Bling crystals - Temple tips
Ref. 01415
Silicone glue - 9 ml 10’ ÷ 12’ min.
RUBBER INSERT FOR ACETATE FLEX SIDE
Ref. 01267
20 pcs.
Ø 2,6 mm
Ref. 01268
20 pcs.
Ø 4,5 mm
Ref. 01269
20 pcs.
Ø 6,0 mm
Rubber ring decreases the gap between the Acetate Flex side and Front Part.
DOUBLE SIDE ADHESIVE LENS INTERLINER
THIN Ref. 01266
• Prevents rotation of the astigmatism axis.
• Sticks the lens to the groove.
• Ideal for thick toric lenses.
• Easy to apply. 16 m
Ref. 01873
LENS WASHER KIT
Ref. 01250, 01251, 01254, 01255, 01260, 01266.
Tray included, suitable for new LMS Cube.
THREAD LOCK 5.2
To block and seal screws and nuts
ergo® Made in Switzerland
All Ergo bottles come with Patented "No Waste" Dispenser
• "Drop by drop" release for precise application
• "Anti-desiccation" system: After use, remove glue from nozzle to avoid obstruction.
The nozzle does not spill and the glue does not dry out, allowing the complete contents of the bottle to be used up.
BLUE GREEN
MEDIUM STRENGTH OIL TOLERANT
HIGH STRENGTH LOW VISCOSITY
ADHESIVES FOR FRAMES 5.2
Cyanoacrylate adhesives - Mineral filler
Complete hardening after 24 hours, for best chemical and mechanical resistance.
UNIVERSAL FOR PLASTIC - RUBBER METAL LEATHER
Ref. 01422 ergo® 5012
Instant superglue - 5 g 2” ÷ 30”
UNIVERSAL FOR PLASTIC - RUBBER METAL LEATHER
Ref. 01405
LOCTITE 401
Instant
ACETATE GRILAMID OPTYL RUBBER - NEOPRENE
Ref. 01423 ergo® 5300
Instant superglue - 20 g 2” ÷ 30”
SPECIAL FOR GLASSES
ANAEROBIC GLUE FOR METAL - PLASTIC CERAMIC - WOOD INNOVATIVE FORMULA
The glue remains liquid giving more time to position the parts to be joined and hardens only in the absence of air.
Ref. 01421 GLUE 21
Anti-halo - 20 g 7” ÷ 45”
MINERAL FILLER FOR CYANOACRYLIC GLUES
Ref. 01428 ergo® 5000 30 g +
ADHESIVES FOR LENSES GLUE REMOVER 5.2
Cyanoacrylate adhesives and silicone glue - Glue Remover Gel
CR39
HIGH INDEX
Suitable for plastic and metal frames
Ref. 01406 Halo-Free LOCTITE 460
Instant superglue - 20 g 2” ÷ 40”
With dispensing needle
GLUE REMOVER GEL
UNIVERSAL FOR CYANOACRYLATE GLUES
Ref. 01429 Liquid Gel ergo® 9153
Does not leak - 20 g 60’ ÷ 90’ min.
FOR GLASS POLYCARBONATE METAL AND VARIOUS MATERIALS
Ref. 01415
HYPO-TUBE CEMENT
Silicone glue - 9 ml 10’ ÷ 12’ min.
Liquid lens liner
suitable for:
• Rimless
• Bling crystals
• Temple tips
Easy application.
The cap with dispensing needle allows the glue to keep flowing freely.
UV GLUE FOR RIMLESS FRAMES 5.2
FOR PLASTIC AND METAL FRAMES OR LENSES
Ideal for filling in rimless drill holes, suitable on any kind of material.
The transparent gel hardens through UV rays and can be drilled once completely dried.
The glue hardens only under UV rays in approx. 10-12 minutes.
It must completely crystallize before it can be further processed.
The crystallization process normally takes 24 hours.
The UV lamp reduces the crystallization time to approx. 2 minutes and guarantees perfect transparency.
Ref. 01419
UV-FIX
With dispensing needle - 10 g
10’ ÷ 12’ min.
Bottle
LENS AND FRAME CLEANING IN THE LAB 5.3
Concentrated detergents for ultrasonic cleaners
Do not corrode the frames or lenses
High cleaning capacity, enhanced by the mechanical effect of the ultrasound
ACTIVE LIQUID WITH ANTIBACTERIAL PROPERTIES
Thanks to its active enzymes, this detergent can also be used without ultrasonic cleaner, just with lukewarm water. Its antibacterial properties sanitize the spectacles.
Made in italy - 100% NO ALCOHOL
Ref. 06859 1 litre bottle concentrated
Add one/two cupfuls of detergent to 1 litre of water
Ultrasonic cleaners employ high frequency energy that is generated electronically by a transmitter in the unit.
The electrical energy is then transformed into sound waves by a device known as a transducer.
Ultrasonic cleaners are easy to operate, require no maintenance and are economical to utilise due to the semiconductors technology.
They are the ideal equipment for the cleaning of frames and parts.
OPTOCLEAN
Cleaning concentrate specifically for ultrasonic cleaners.
Made in Germany.
Ref. 05491 1 litre bottle concentrated
Add one/two cupfuls of detergent to 1 litre of water
LENS AND FRAME CLEANERS 5.3
Spray Clean with antibacterial properties, 0% alcohol
Sanitizing detergent for frames and lenses, suitable for AR coated lenses.
Wipe dry with microfiber cloth
INSTRUCTIONS FOR THE USE OF YOUR SPECTACLES
CLEANING
Use only recommended products and liquid neutral cleaners and wipe dry with a suitable cloth. Use water if you do not have any recommended products. Do not use corrosive agents, neither alcohol or non-specific detergents, unless otherwise indicated.
ANTIBACTERIAL SPRAY CLEAN
Ref. 11945
3 bottles of 150 ml each
Ref. 11935
Refill - 1 litre bottle
MICROFIBRE GLOVES
Ref. 10490
White Medium size 1 pair
KING SIZE
MICROFIBRE
35x40 cm
For the practice, the optical workshop and retail gift.
Ref. 11992
6 pcs. assorted colours: grey, light brown, green Individually packed.
Ref. 11999
3 pcs. assorted colours
Suction cup included.
INK REMOVER 5.3
To remove the marking on progressive lenses
SUPPLYING THE GLASSES TO THE CUSTOMER
The presence of the original markings on progressive lenses allows to check the correct position of the optical centres. After this, marks can be easily removed with the Ink Remover Pen (Ref. 06973) or with the Ink Remover Spray (Ref. 06976).
INK REMOVER PEN
FELT PEN
Ref. 06973 8 gr 1 pc.
INK REMOVER BOTTLES FOR THE PRACTICE AND THE LAB
SPRAY
Ref. 06976
Bottle 150 ml 3 pcs./pkg.
REFILL Ref. 06857
Bottle 1 litre 1 pc.
Centro Style marking ink cleaning solution is suitable for all types of lenses, AR coated, teflon® treated, progressive CR39 and PC lenses. Spray onto the lens and wipe with a microfiber cloth.
To mark lenses
WATERPROOF PERMANENT MARKER PENS FOR NORMAL LENSES
Ref. 06960
Red, fine 0.6 mm
5 pcs.
Ref. 06962
Black, fine 0.6 mm
5 pcs.
SPECIAL MARKERS
FOR TEFLON® COATED LENSES / SUPERHYDROPHOBIC
Ref. 06964
Black, extra-fine 0.4 mm 5 pcs.
Ref. 06965
Black, fine 0.6 mm 5 pcs.
Ref. 06966
Red, fine 0.6 mm 5 pcs.
WATER SOLUBLE NON PERMANENT MARKER
Ref. 06970
Black, extra-fine 0.4 mm
Ideal to mark Press-On™. 5 pcs.
INK FOR CENTERING DEVICES
WHITE PENCIL
IDEAL FOR SUN LENSES
Ref. 06969 3 pcs.
INK FOR LENSMETERS
Ref. 06982
Red 30 ml 1 pc.
RIPPLED BLOCKS AND LENS CLAMP ADAPTOR 5.4
For Automatic Lens Edgers
FOR W./B. HAND EDGERS
Ref. 07368
Ø 25 mm.
Block Ø 16 mm 10 pcs.
Ref. 07382
Ø 25 mm.
Block Ø 16 mm
For curved lenses 10 pcs.
Ref. 07370
Ø 25 mm.
Block Ø 16 mm 2 pcs.
Ref. 07375
Ø 25 mm
Block Ø 14 mm 5 pcs.
FOR N. HAND EDGERS
Ref. 07377
30x17 mm
Block Ø 12 mm
For curved lenses - 5 pcs.
Ref. 07369
25x20 mm
Block Ø 16 mm 10 pcs.
Ref. 07367
25x17 mm
Block Ø 15 mm 2 pcs.
DEBLOCKING PLIERS
Ref. 07362
25x20 mm
Block Ø 16 mm 2 pcs.
Ref. 07376 Ø 18 mm
Block Ø 14 mm 5 pcs.
Ref. 07380
30x17 mm
Block Ø 12 mm 5 pcs.
FOR E. MR. B./O. HAND EDGERS
Ref. 07378
Ø 22 mm
Block Ø 15,5 mm 10 pcs.
FOR E.K. ETG. HAND EDGERS
Ref. 07371
Ø 25 mm
Block Ø 15,5 mm 20 pcs.
FOR H. TZ. HAND EDGERS
Ref. 07388
25x17 mm 4 pcs. (2 pairs)
Flexible Lens Clamp Adaptor for W.B.
Ref. 07384
Ø 25 mm 2 pcs.
Ref. 07379
18x14 mm
Block 15,5x14 mm 10 pcs.
Ref. 07372
Ø 18 mm
Block Ø 15,5 mm 10 pcs.
Ref. 07389 20x17 mm 4 pcs. (2 pairs)
Ref. 03450N
Ref. 03452N
Ref. 07385
Ø 19 mm 2 pcs.
DEBLOCKING PLIERS
FOR SEMIRIGID BLOCKS
Ref. 03453N
Ref. 03455N
LENS SURFACE DISKS AND TAPE 5.4
Used in conjunction with blocking pads to prevent lens slippage
Adhesive protector
PROTECTOR DISKS Ø 30 mm
Ref. 07330 1000 pcs.
FOR RIMLESS FRAME ASSEMBLY BLUE ROUND
Ref. 07327 100 pcs.
Holes D=2,0 mm Slot 7x3 mm NEW
Clear 32x17 mm
VIDEO
For lenses with hydrophobic and super-hydrophobic coating
FOR LENS CURVES UP TO BASE 6 / +4.5 DPT.
Ref. 07331 500 pcs.
Clear elliptical 40x26 mm
Ref. 07335 500 pcs.
FOR LENSES WITH HIGH WRAP-AROUND INCLINATION
Ref. 07333 500 pcs.
Clear elliptical 40x26 mm
FOR VERY SLIPPERY SUPER-HYDROPHOBIC LENSES
Ref. 07339 500 pcs.
Gold elliptical 40x26 mm
Clear rectangular 40x18 mm
Provides excellent adhesion to hydrophobic and super-hydrophobic lens coatings to prevent lenses from “twisting” and “slipping” off-axis while edging.
INSTRUCTIONS FOR USE
With common adhesive pads apply one disc to each side of the lens.
With hydrophobic and super hydrophobic adhesive pads apply only one disk to the inside of the lens.
FOR COATED LENSES 5.4
Thickness 0,4 mm - 3M Quality
CR39, High Index, Shatterproof, Glass lenses
FOR SMALL AND HALF-EYE LENSES
20x24 mm
Ref. 07359 1000 pcs.
• Excellent torque force resistance
• Excellent adhesion
• Ideal for standard lenses
For W and B edgers - 0,4 mm
For W and B edgers - 0,4 mm
FOR FULL-EYE LENSES
For E and TP edgers - 0,8 mm
For E and TP edgers - 0,4 mm
Ø 24 mm
Ref. 07357 1000 pcs.
For N edgers - 0,4 mm
17x31 mm
Ref. 07351 1000 pcs.
FOR FULL-EYE LENSES
FOR COATED LENSES 5.4
Thickness 0,6 mm - 3M Leap™ III
CR39, High Index, Shatterproof, Glass lenses
FOR SMALL AND HALF-EYE LENSES
18x24 mm
Ref. 07349 1000 pcs.
• Excellent torque force resistance
• Excellent adhesion
• Ideal for lenses with thin centre (negative powers)
FOR FULL-EYE LENSES
24x24 mm
Ref. 07345 1000 pcs.
FOR SMALL AND HALF-EYE LENSES FOR FULL-EYE LENSES
Ø 18 mm
Ref. 07348 1000 pcs.
Ø 24 mm
Ref. 07344 2000 pcs.
Ø 26 mm
Ref. 07346 1000 pcs.
FOR FULL-EYE LENSES
17x31 mm
Ref. 07347 1000 pcs.
FOR COATED LENSES 5.4
Thickness 0,8 mm
CR39, High Index, Shatterproof, Glass lenses
FOR SMALL AND HALF-EYE LENSES
20x24 mm
Ref. 07354 1000 pcs.
• Very good torque force resistance
• Very good adhesion
• Excellent quality/price ratio
• Ideal for lenses with thin centre (negative powers)
FOR SMALL AND HALF-EYE LENSES
For E and TP edgers - 0,8 mm
For W and B edgers - 0,8 mm
Ø 18 mm
Ref. 07350 1000 pcs.
Ø 24 mm
Ref. 07356 1000 pcs.
For E and TP edgers - 0,8 mm
Ø 22 mm
Ref. 07340 1000 pcs.
For N edgers - 0,8 mm
For W and B edgers - 0,8 mm
FOR FULL-EYE LENSES
For E and TP edgers - 0,8 mm
FOR FULL-EYE LENSES
17x31 mm
Ref. 07355 1000 pcs.
FOR HYDROPHOBIC LENSES 5.4
Thickness 0,8 mm - Optisafe®
CR39, High Index, Shatterproof, Glass lenses
FOR SMALL AND HALF-EYE LENSES
18x29 mm
Ref. 07314 1000 pcs.
• Excellent torque force resistance
• Excellent adhesion
• Ideal for standard lenses
For W and B edgers - 0,8 mm
FOR SMALL AND HALF-EYE LENSES
Ø 18 mm
Ref. 07312 1000 pcs.
Ø 24 mm
Ref. 07310 1000 pcs.
For E and TP edgers - 0,8 mm
Ø 22 mm
Ref. 07311 1000 pcs.
For N edgers
0,8 mm
17x31 mm
Ref. 07315 1000 pcs.
For W and B edgers - 0,8 mm
PER SAGOME NORMALI
For E and TP edgers - 0,8 mm
PER SAGOME NORMALI
-FOR SUPERHYDROPHOBIC LENSES 5.4
Thickness 0,9 mm
CR39, High Index, Shatterproof, Glass lenses
FOR SMALL AND HALF-EYE LENSES
20x24 mm
Ref. 07294 1000 pcs.
PREMIUM FORMULA
• Excellent torque force resistance
• Excellent adhesion
• Ideal for lenses with thin centre (negative powers)
Support side, adhesive: Acrylic, red fingerlift
Lens side, adhesive: Polysiloxane, yellow fingerlift
The coloured fingerlifts help in correctly positioning the blocking pad: red for the support, yellow for the lens.
FOR SMALL AND HALF-EYE LENSES
Ø 18 mm
Ref. 07292 1000 pcs.
Ø 24 mm
Ref. 07290 1000 pcs.
FOR FULL-EYE LENSES
14x21 mm
Ref. 07293 1000 pcs.
Ø 22 mm
Ref. 07291 1000 pcs.
FOR FULL-EYE LENSES
17x31 mm
Ref. 07295 1000 pcs.
For W and B edgers - 0,9 mm For N edgers - 0,9 mm For N edgers - 0,9 mm For E and TP edgers - 0,9 mm For E and TP edgers - 0,9 mmFORMERS
To be shaped with punch, miller cutter or scissors
Ref. 07400
Trasparent - Shape with punch cutter or scissors.
Dim.: 75x60x1.5 mm - 250 pcs.
Ref. 07411
Green - Shape with punch cutter or scissors.
Dim.: 70x60x2.0 mm - 250 pcs.
Ref. 07421
White - Shape with miller cutter.
Dim.: 70x60x2.5 mm - 250 pcs.
Ref. 03782
Scissor for easy pattern cutting
Cleaning and dressing diamond sticks
Ref. 06852
A broad spectrum powder defoamer, BPI NO FOAM™ controls foam build up in glass and plastic surfacing and edging operations. Long lasting and readily dispersable, NO FOAM™ is an economical solution to ophthalmic foaming problems. Dilute one bottle into 20 litres of water. 60 gr
Ref. 07300
Coarse 120G
Dim.: 150x24 mm 6 pcs.
WATER MAKE UP LENS 5.5
Multicolour edge customising: an exclusive service!
Ref. 07231
Grey col. 5330
Ref. 07232
Black col. 4
Ref. 07233
Dark Brown col. 5340
Ref. 07234
Dark Green col. 5332
Ref. 07235
Bordeaux col. 5333
Ref. 07236
Turquoise col. 5341
LENS MAKE UP is a special felt pen to decorate:
• The lens edge of rimless and supra glasses. Suitable for CR39, crystal, polycarbonate and acrylic lenses.
• Each pen can colour up to 300-500 lens pairs.
• Available in 6 classic colours.
WATER MAKE UP FRAMES 5.5
Water felt pens to retouch frames - Multicolour metallic paints
FRAME MAKE UP is a special felt pen to:
• Colour frames
• Colour screws, pad arms or other parts
• Retouch scraped parts
• Retouch sweat-eaten temples.
Ref. 07209 Clear Shiny 001
Ref. 07210 Yellow Gold 003
Ref. 07211 White 7364
Ref. 07201 Gun Metal 016
Ref. 07202 Silver 7370
Ref. 07203 Matt Night Blue 038
Ref. 07204 Genuine Wine 108
Ref. 07205 Antique Brown 009
Ref. 07206 Shiny Bordeaux 014
Ref. 07207 Satin Black 005
Ref. 07208 Shiny Black 004
Ref. 07212 Dark Avana 011
INSTRUCTIONS
• Clean thoroughly the part to be repaired.
• Shake felt pen very well before use.
• Press felt and apply colour onto the frame.
• Allow to air dry for 15 minutes.
• Warm in frame heater to speed up drying.
MAKE UP FRAME KIT
Ref. 07200
Full assortment of 12 pens.
TOUCHUP BRUSHES 5.5
For customising your frames, contents 12 ml.
METALLIC
Ref. 07110
Metallic Silver
Ref. 07111
Metallic Gold
Ref. 07121
Metallic Blue
Ref. 07120
Metallic Gun Metal
CLASSIC
Ref. 07100
Shiny Black
Ref. 07104 Matt Black
Ref. 07106 Brown
Ref. 07109 Blue
Ref. 07112
Fire red
INSTRUCTIONS
• Shake well before use.
• Apply an even layer of lacquer with the cap brush.
• Wait a few minutes until it dries.
• To obtain tortoise effect, brush again irregularly.
Ref. 07116
Clear
Ref. 07117
White
TOUCH-UP BRUSH KIT
Ref. 07118
Set of 12 lacquers. (Ref. 07100 Shiny Black - 2 pcs.)
POLISHING COMPOUNDS 5.6
For polishing and glossing of metal and plastic
HARD POLISHING - MATT FINISH FOR ACETATE FRAMES - METAL FRAMES - LENSES
Ref. 05280
Sand compound - 300 g
For acetate frames
Ref. 05285
White compound - 300 g
For white metal frames and CR39 lens edges
FINE POLISHING AND GLOSSING FOR ACETATE FRAMES - METAL FRAMES - LENSES
Ref. 05282
White compound - 250 g
For acetate frames and glass lens edges
Ref. 05286
Green compound - 300 g
For white metal frames
LENS EDGE POLISHING AND GLOSSING
Ref. 05291
Ivory compound - 300 g
For polycarbonate lenses.
Ref. 05289
Yellow compound - 250 g
For gold metal frames
INSTRUCTIONS
• Apply polishing compound in a thin even layer to mop. Repeat frequently.
• Slightly increase pressure when processing glass lenses.
• After polishing wipe off compound residuals with a soft cloth.
• Clean frame in ultrasonic bath.
POLISHING WHEELS AND COMPOUNDS FOR FRAMES 5.6
For polishing and glossing metal and plastic frames
ACETATE FRAMES
Ref. 01880
SET OF WHEELS AND COMPOUNDS FOR ACETATE FRAMES
Wheels: Ref. 05200, 05205, 05225
Compounds: Ref. 05280, 05282.
Tray included, suitable for new LMS Cube.
FOR WHITE OR GUN METAL FRAMES
Ref. 01882
SET OF WHEELS AND COMPOUNDS FOR WHITE OR GUN METAL FRAMES
Wheels: Ref. 05200, 05205, 05225
Compounds: Ref. 05285, 05286.
Tray included, suitable for new LMS Cube.
GOLD METAL FRAMES
Ref. 01884
SET OF WHEELS AND COMPOUNDS FOR GOLD METAL FRAMES
Wheels: Ref. 05200, 05205, 05225
Compounds: Ref. 05289.
Tray included, suitable for new LMS Cube.
CLEANING AND DE-SCALING BRUSHES
Ref. 05235
Brass wire
Ø 90 mm 8 mm
Bore Ø 6.5 mm
POLISHING MOPS
Ref. 05205
Cotton
Ø 120 mm 10 mm
Bore Ø 8 mm
Ref. 05220
Cotton
Ø 100 mm 6 mm
Tapered bore from Ø 8 a 6.5 mm
POLISHING STEPS 5.6
Technical advice
POLISHING
Apply gentle pressure to avoid overheating.
FINE POLISHING
Apply gentle pressure to avoid overheating. Use a thin layer of compound frequently.
GLOSSING
Apply gentle pressure to avoid overheating. After glossing always wipe off compound residue with a soft cloth. Clean in ultrasonic bath.
Wheels
POLISHING
Apply gentle pressure to avoid overheating.
FINE POLISHING
Apply gentle pressure to avoid overheating. Use a thin layer of compound regularly.
GLOSSING
Apply gentle pressure to avoid overheating. After glossing always wipe off compound residue with a soft cloth. Clean in ultrasonic bath.
HARD POLISHING
Apply gentle pressure to avoid overheating.
POLISHING
Apply gentle pressure to avoid overheating.
FINE POLISHING
Apply gentle pressure to avoid overheating. Use a thin layer of compound regularly.
GLOSSING
Apply gentle pressure to avoid overheating. After glossing always wipe off compound residue with a soft cloth. Clean in ultrasonic bath.
FINE POLISHING MOPS
Ref. 05200
Flannel
Ø 120 mm 10 mm
Bore Ø 8 mm
Ref. 05205
Ref. 05220 Cotton
Ref. 05200
rpm Compounds
Ref. 05280 Sand
Ref. 05282 White
Ref. 05225 Soft cotton Ref. 05282 White
Ref. 05205
Ref. 05220 Cotton
Ref. 05200 Flannel
Ref. 05285 White
Ref. 05286 Green
Ref. 05225 Soft cotton Ref. 05286 Green
Ref. 05235 Brass wire
Ref. 05205
Ref. 05220 Cotton
Ref. 05200 Flannel
Ref. 05225
GLOSSING MOP
Ref. 05225
Soft cotton
Ø 100 mm 35 mm
Tapered bore from Ø 9 to 6.5 mm
Reinforced wooden centre
No compound required
Ref. 05289 Yellow
Ref. 05289 Yellow
POLISHING WHEELS AND COMPOUNDS FOR LENSES 5.6
For polishing and glossing CR39, polycarbonate or glass lenses
CR39 LENSES
POLYCARBONATE LENSES
Ref. 01886
SET OF WHEELS AND COMPOUNDS FOR CR39 AND POLYCARBONATE LENSES
Wheels: Ref. 05225, 05226, 05228
Compounds: Ref. 05282, 05285, 05291.
Tray included, suitable for new LMS Cube.
GLASS LENSES
CR39 AND POLYCARBONATE LENS POLISHING
Ref. 05226
Hard felt for flat edge polishing.
Ø 100 mm 20 mm
Bore Ø 6 mm
Ref. 05228
Hard felt, for bevel and flat edge polishing.
Ø 70 mm 20 mm
Bore Ø 6 mm
POLISHING STEPS 5.6
Technical advice
POLISHING
Apply gentle pressure to avoid overheating.
Use a thin layer of compound. Apply frequently.
GLOSSING
Apply gentle pressure to avoid overheating.
After glossing, always wipe off compound residue with a cloth.
Clean in ultrasonic bath.
POLISHING
Apply gentle pressure to avoid overheating.
Use a thin layer of compound.
Apply frequently.
GLOSSING
Apply gentle pressure to avoid overheating.
After glossing, always wipe off compound residue with a cloth.
Clean in ultrasonic bath.
POLISHING
Apply slightly more pressure, keep lens turning. After polishing always wipe off compound residue with a cloth.
Clean in ultrasonic bath.
FOR COMPACT GLOSSING WITH COMPOUND
Ref. 05225
Soft cotton
Ø 100 mm 35 mm
Tapered bore from Ø 9 to 6.5 mm
Reinforced wooden centre
Wheels
Compounds
Ref. 05226 Hard felt Ref. 05285 White
Ref. 05228 Hard felt with groove
Ref. 05225
Ref. 05285 White
Ref. 05226 Hard felt
Ref. 05228 Hard felt with groove Ref. 05291 Ivory
Ref. 05225
Ref. 05226 Hard felt
Ref. 05228 Hard felt with groove
Ref. 05282 White
Ref. 05282 White
WATERSOLUBLE
POWDERS 5.7
WATERSOLUBLE DYEING POWDERS 5.7
Biodegradable - For CR39 - High index - Polycarbonate - 10 g sachets
MAUVE Ref. 0684
INSTRUCTIONS
ORANGE Ref. 06846
SUITABLE FOR NIGHT DRIVING
• Heat 1 litre of demineralized water at 60°C and add the bag with the dye.
• Heat solution to 93 °C and dip lens in using lens holder Ref. 06525.
• Different hues can be obtained by varying the dipping times. The sachet protects the tint powders indefinitely. Check the UV transmission with our UV & Visible Spectrotester Ref. 05053.
Printed colours may vary from actual lens tint.
BPI LIQUID DYES FOR LENSES 5.7
The dye molecules bond to the chemical structure of the lens and become part of it. Colours are more stable and the colouring time is faster.
Mix 88 ml of dye with 1 litre of distilled water. Printed colours may vary from actual lens tint.
NOT SUITABLE FOR DRIVING. SIGNAL LIGHT COLOURS ARE NOT ALWAYS DISTINGUISHABLE.
BPI LIQUID DYES FOR LENSES 5.7
Clear CR39 lenses for tinting
Base | Ø 73 mm | UV360 | Cat. 0 12 pcs. B 6
INSTRUCTIONS FOR USE
• Dissolve the contents of one bottle into 1 litre of distilled water at 60°C.
• Heat solution to 93°C and dip lens in.
• Different hues can be obtained by varying the dipping times.
• Check the UV transmission with our UV & Visible Spectrotester Ref. 05053.
Printed colours may vary from actual lens tint.
Base | Ø 76 mm | UV360 | Cat. 0 12 pcs. B 8
5.7
NEUTRALIZER SOLUTION
Neutralizer solutions for CR39
NEUTRALIZER SOLUTION FOR CR39
Ref. 06850
Removes dye from organic lenses. Non flammable.
1 litre bottle of concentrated solution.
INSTRUCTIONS
• Dilute with distilled water, ratio 1:20.
• Heat to 90°C.
• Dip the lens until the required decolouring grade has been achieved.
CHEMICALS
UV Diamond Dye 400 XL - Heating Fluid
UV DIAMOND DYE 400 XL
Ref. 06945
• Absorbs up to 99% of UV light under 400 nm.
• Increases scratch resistance.
Lens will not turn yellow and no oven required.
Bottle 450 ml
INSTRUCTIONS
UV treatment must be applied before tinting.
• Mix equal parts with distilled water.
• Heat to 92°C-95°C in a clean container
• Clean the lens before treatment.
• Using a clean lens holder, immerse the lens for 10-15 min.
Immersion time varies according to the thickness of the lens.
HEATING FLUID
Ref. 06851
Heating fluid to be used with plastic lens coloring equipments, formulated to maintain a high level of heat when coloring plastic lenses. High entropy.
1000 ml Bottle ready for use
INSTRUCTIONS
Make sure that the strength of the machine has been properly cleaned and dried so that the GL 77 is not contaminated.
Pour the GL-77 into the appliance to colour and fill it up to the middle, making sure to cover the resistance when all the tanks are in place. Check the level monthly and top up if necessary. If contaminated replace it completely. The equipment must be turned off and the resistance must cool down before adding GL-77. Do not mix GL-77 with water or other solutions. GL-77 is not toxic and is not flammable when used as directed. Do not exceed 300°F.
SOLDERING WIRE AND CONSUMABLES 5.8
SOLDER RODS
Solder and flux combined for ready use.
Ideal for nickel-silver, monel and stainless steel metal.
CADMIUM FREE
SOLDER WIRE
All-purpose soldering wire in silver alloy (40%).
Easy flowing, suitable for nickel silver and monel metal.
Melting range: 610°C - 650°C.
To be used together with borax flux (Ref. 06208).
Ref. 06200
Solder wire Ø 0.5 mm.
Length: 2.5 m.
Ref. 06202
Solder wire Ø 0.3 mm.
Length: 2.5 m.
Flux
Ref. 06210
Soft yellow solder.
Melting range: 655°C - 680°C
Pack of 10 rods - 250 mm each
Ø 1,15 mm
Ref. 06214
Yellow gold solder.
Melting range: 605°C- 635°C
Pack of 10 rods - 250 mm each
Ø 1,15 mm
BORAX
Promotes quick and easy flow of solder between the surfaces being soldered.
Melting range: 500°C - 700°C.
Ref. 06208
Borax flux powder to be mixed with hot distilled water to make a paste.
SOLDERING CONSUMABLES
ISOFLAM
Ref. 06221
Heat shielding paste. It will protect the non-soldered area by dissipating heat for temperatures up to 3,000°C (5,432°F).
It isolates parts close to the soldering point and reduces the risk of damage to plastic and painted parts. It does not stain and washes off in water. 50 g
100 g
SOLDERING AND PLATING CONSUMABLES 5.8
CONSUMABLES FOR MINIFLAM
GAS FOR MINIFLAM
Ref. 06108
Butane gas. 400 ml bottle.
CONSUMABLES
Ref. 06020
Caustic solution
Electrolyte 0.5 litre - 2 pcs.
Ref. 06022
FOR SOLDERING UNITS
Boric acid solution - flux 0.5 litre
FOR AIRFREIGHT DELIVERIES
Ref. 06055
Boric acid in grains
25 g
PLATING SOLUTIONS
Ref. 06411
Gold plating solution
50 ml
Ref. 06415
Palladium plating solution
50 ml
Ref. 06423
• Clamp electrode
• Brush electrode
SOLDERING STEPS 5.8
PREPARATION
• Always wear safety glasses.
• First, remove any parts that will be affected by heat, e.g. pads, rim cover, temple tips.
• Before heating, it may be necessary to apply a large amount of protective heat shield paste ISOFLAM (Ref. 06221) over those parts that are close to the area being heated.
• Next, remove broken part by heating the area until it becomes detached. Use tweezers Ref. 03730 to help.
POLISHING
• Always prepare the surfaces to be soldered first by using the rubber abrasion wheels (Ref. 02444 - Ref. 02447).
A clean, smooth surface ensures a good result.
• Alternatively use a file.
PROTECTION OF THE PARTS CLOSE TO THE SOLDERING POINT
• Apply ISOFLAM protection paste (Ref. 06221) around the soldering point and on any components (nose pads, enamelled parts, etc.).
• After soldering, the paste can be recovered and reused by adding a few drops of distilled water.
POSITIONING OF THE FRAME
• Place the frame on the soldering table (Ref. 06195) to give easy access to the part being soldered. The clamps should be kept away from the soldering area to avoid overheating.
• Rest your elbows to support the hands.
• The parts to be soldered should not be close to the table top.
PLANNING THE SOLDER
• If you are not using SOLDER rods (Ref. 06210-6214), prepare the solder wire (Ref. 06200-06202) in advance by wetting it and dipping it in borax flux powder (Ref. 06208).
• Always heat first the thicker surface as it reaches the melting point in longer time by absorbing more heat.
• Dip the soldered part in water.
• Use protective goggles during all soldering steps.
SOLDERING STEPS 5.8
Use of the different solder alloys
POLISHING
FRONT HINGE PLATE
The part connecting the temple hinge to the eye wire rim is subject to great stress. Having a large supporting surface it is recommended to use the solder rods
Ref. 06210 - Ref. 06214, or the 0.5 mm solder wire
Ref. 06200.
RIM CLOSING BLOCK
When soldering the closing block to the rim, as the surface area is quite small, it is recommended that a small amount of solder is carefully placed. Recommend 0.3 mm wire
Ref. 06202.
HINGES
Part of the frame that allows the temple to pivot.
Recommended to use the solder rods Ref. 06210 and Ref. 06214, or the 0.5 mm solder wire Ref. 06200.
After de-scaling remove and smooth residues of solder with rubber abrasion wheels (Ref. 02444 -Ref. 02447).
Alternatively, use the brass (Ref. 02421) or steel brushes (Ref. 02422).
Next polish with silicone wheels (Ref. 02442) or hard felt brushes (Ref. 02429).
CLEANING
For best results clean the frame with an ultrasonic cleaner using concentrated detergent for ultrasonic cleaners, not to damage the frames and any type of lenses.
High cleaning capacity enhanced by the mechanical action of the ultrasonic cleaner.
FINISHING
To touch-up soldered parts use these coloured lacquers. Ideal for individualising or personalising frame parts.
ACTIVE LIQUID WITH ANTIBACTERIAL PROPERTIES
Thanks to its active enzymes, this detergent can also be used without ultrasonic cleaner, just with lukewarm water. Its antibacterial properties sanitize the spectacles.
Ref. 06859 1litre bottle
Add one/two cupfuls of detergent to 1 litre of water. 100% NO ALCOHOL
TOUCHUP BRUSH KIT
Ref. 07100 - 07104 - 07106 - 0710907110 - 07111 - 07112 - 0711607117 - 07120 - 07121.
Ref. 07118
Set of 12 lacquers. (Ref. 07100 Shiny Black - 2 pcs.)