Matrix Effect

Abstract The influence of the organic content, sample preparation process and the morphology of the depositions of two types of Coke beverage, traditional and light Coke, have been investigated by mean of Total-reflection X-ray Fluorescence (TXRF) spectrometry. Strong distortions of the nominal concentration values, up to 128% for P, have been detected in the analysis of traditional Coke by different preparation methods. These differences have been correlated with the edge X-ray energies of the elements analyzed being more pronounced for the lighter elements. The influence of the organic content (mainly sugar) was evaluated comparing traditional and light Coke analytical TXRF results. Three sample preparation methods have been evaluated as follows: direct TXRF analysis of the sample only adding internal standard, TXRF analysis after open vessel acid digestion and TXRF analysis after high pressure and temperature microwave-assisted acid digestion. Strong correlations were detected between quantitative results, methods of preparation and energies of the X-ray absorption edges of quantified elements. In this way, a decay behavior for the concentration differences between preparation methods and the energies of the X-ray absorption edges of each element were observed. The observed behaviors were modeled with exponential decay functions obtaining R2 correlation coefficients from 0.989 to 0.992. The strong absorption effect observed, and even possible matrix effect, can be explained by the inherent high organic content of the evaluated samples and also by the morphology and average thickness of the TXRF depositions observed. As main conclusion of this work, the analysis of light elements in samples with high organic content by TXRF, i.e. medical, biological, food or any other organic matrixes should be taken carefully. In any case, the direct analysis is not recommended and a previous microwave-assisted acid digestion, or similar, is mandatory, for the correct elemental quantification by TXRF.

This paper describes development, optimization and validation of a method for the simultaneous determination of 29 multi-class pharmaceuticals using off line solid phase extraction (SPE) followed by liquid chromatography-triple quadrupole mass spectrometry (LC-MS-MS). Target compounds include analgesics and non-steroidal anti-inflammatories (NSAIDs), lipid regulators, psychiatric drugs, anti-histaminics, anti-ulcer agent, antibiotics and beta-blockers. Recoveries obtained were generally higher than 60% for both surface and wastewaters, with exception of several compounds that yielded lower, but still acceptable recoveries: ranitidine (50%), sotalol (50%), famotidine (50%) and mevastatin (34%). The overall variability of the method was below 15%, for all compounds and all tested matrices. Method detection limits (MDL) varied between 1 and 30ng/L and from 3 to 160ng/L for surface and wastewaters, respectively. The precision of the method, calculated as relative standard deviation (R.S...

A procedure is proposed for the direct determination of manganese and iron in wine employing fast sequential flame atomic absorption spectrometry and the reference element technique to correct for matrix effects. Cobalt, silver, nickel and indium have been tested as reference elements. The results demonstrated that cobalt and indium at a concentration of 2 and 10 mg L−1 were efficient for quantification of manganese and iron, respectively. Under these conditions, manganese and iron could be determined with quantification limits of 27 and 40 μg L−1, respectively. The proposed method was applied to the determination of manganese and iron in 16 wine samples. The content of manganese varied from 0.78 to 2.89 mg L−1 and that of iron from 0.88 to 9.22 mg L−1. The analytical results were compared with those obtained by inductively coupled plasma optical emission spectrometry after complete mineralization using acid digestion. The statistical comparison by a t-test (95% confidence level) showed no significant difference between the results.

The production of short-chained volatile fatty acids (VFAs) by the anaerobic bacterial digestion of sewage (wastewater) affords an excellent opportunity to alternative greener viable bio-energy fuels (i.e., microbial fuel cell). VFAs in wastewater (sewage) samples are commonly quantified through direct injection (DI) into a gas chromatograph with a flame ionization detector (GC-FID). In this study, the reliability of VFA analysis by the DI-GC method has been examined against a thermal desorption (TD-GC) method. The results indicate that the VFA concentrations determined from an aliquot from each wastewater sample by the DI-GC method were generally underestimated, e.g., reductions of 7% (acetic acid) to 93.4% (hexanoic acid) relative to the TD-GC method. The observed differences between the two methods suggest the possibly important role of the matrix effect to give rise to the negative biases in DI-GC analysis. To further explore this possibility, an ancillary experiment was performed to examine bias patterns of three DI-GC approaches. For instance, the results of the standard addition (SA) method confirm the definite role of matrix effect when analyzing wastewater samples by DI-GC. More importantly, their biases tend to increase systematically with increasing molecular weight and decreasing VFA concentrations. As such, the use of DI-GC method, if applied for the analysis of samples with a complicated matrix, needs a thorough validation to improve the reliability in data acquisition.

In Inductively Coupled Plasma-Atomic Emission Spectroscopy (ICP-AES) spectrochemical analysis, the MgII(280.270 nm)/MgI(285.213 nm) ionic to atomic line intensity ratio is commonly used as a monitor of the robustness of operating conditions. This approach is based on the univocal relationship existing between intensity ratio and plasma temperature, for a pure argon atmospheric ICP in thermodynamic equilibrium. In a multi-elemental plasma in the lower temperature range, the measurement of the intensity ratio may not be sufficient to characterize temperature and electron density. In such a range, the correct relationship between intensity ratio and plasma temperature can be calculated only when the complete plasma composition is known. We propose the combination of the line intensity ratios of two test elements (double ratio) as an effective diagnostic tool for a multi-elemental low temperature LTE plasma of unknown composition. In particular, the variation of the double ratio allows us discriminating changes in the plasma temperature from changes in the electron density. Thus, the effects on plasma excitation and ionization possibly caused by introduction of different samples and matrices in non-robust conditions can be more accurately interpreted. The method is illustrated by the measurement of plasma temperature and electron density in a specific analytic case.

We report a new approach to conduct fast and accurate lithium isotope ratio measurements by MC-ICP mass spectrometry after wet chemical sample preparation. In contrast to most previously published methods our MC-ICP-MS set-up did not use a desolvating system to achieve appropriate ion beam intensities and, therefore, was less affected by matrix-induced shifts of the instrumental mass bias. As the total lithium background and build-up in the sample introduction system was low, previous sample residues could be washed out by an extended uptake of the new sample. Elimination of a nitric acid rinse step increased the sample throughput by a factor of two and allowed the instrumental mass bias drift to be tracked more precisely. δ7Li values of powdered silicate rock reference materials and seawater obtained in this study revealed good accuracy and an overall analytical uncertainty of typically 0.5‰ (2s). On the basis of a comparison between our lithium isotope data and compiled literature data, we recommend preliminary average δ7Li values for seawater (+30.8‰) and several silicate rock reference materials (BHVO-1: +5.0‰; JA-1: +5.6‰; JB-2: +4.8‰). The compilation of published δ7Li values for seawater suggests that the observed large lithium isotope differences are due to inter-method and/or interlaboratory bias. Most recently published δ7Li values for seawater show little variation and confirm a constant lithium isotope composition (at the sub ‰ level) of seawater in well mixed ocean basins.Nous présentons ici une nouvelle méthode permettant d'effectuer des mesures de rapports isotopiques de lithium de façon rapide et précise par spectrométrie de masse ICP-MC, après préparation de l'échantillon par chimie en solution. Au contraire de la plupart des méthodes publiées précédemment, notre protocole d'analyse par MC-ICP-MS n'utilise pas de système de désolvatation pour atteindre les intensités de signaux appropriés et, par conséquent, il est moins affecté par les biais instrumentaux dûs aux effets de matrice. Comme le bruit de fond total et celui qui se construit au cours du temps dans le système d'introduction sont bas, les résidus de l'échantillon précédent peuvent être lavés durant la phase d'introduction de l'échantillon à analyser. L'élimination de l'étape de rinçage par l'acide nitrique augmente la prise d'échantillon d'un facteur deux et permet de suivre plus précisément les variations du biais de masse instrumental. Les valeurs de δ7Li obtenues sur des matériaux de référence certifiés de roche et sur l'eau de mer montrent une bonne justesse et une erreur analytique globale typiquement de O.5‰ (2s). Après comparaison de nos données avec celles compilées dans la littérature, nous recommandons de manière préliminaire les valeurs moyennes suivantes pour l'eau de mer (+30.8‰) et pour quelques matériaux de références de roches silicatées (BHVO-1: +5.0‰; JA-1: +5.6‰; JB-2: +4.8‰). La compilation des valeurs de δ7Li publiées pour l'eau de mer suggère que les grandes différences observées soient principalement dues à des biais entre méthodes et/ou entre laboratoires. Les plus récentes valeurs de δ7Li publiées montrent en effet assez peu de variation et confirment la constance de la composition isotopique en lithium (au niveau du -‰) dans les bassins océaniques bien homogénéisés.

The general strategy to perform anti-doping analyses of urine samples starts with the screening for a wide range of compounds. This step should be fast, generic and able to detect any sample that may contain a prohibited substance while avoiding false negatives and reducing false positive results. The experiments presented in this work were based on ultra-high-pressure liquid chromatography coupled to hybrid quadrupole time-of-flight mass spectrometry. Thanks to the high sensitivity of the method, urine samples could be diluted 2-fold prior to injection. One hundred and three forbidden substances from various classes (such as stimulants, diuretics, narcotics, anti-estrogens) were analysed on a C18 reversed-phase column in two gradients of 9 min (including two 3 min equilibration periods) for positive and negative electrospray ionisation and detected in the MS full scan mode. The automatic identification of analytes was based on retention time and mass accuracy, with an automated tool for peak picking. The method was validated according to the International Standard for Laboratories described in the World Anti-Doping Code and was selective enough to comply with the World Anti-Doping Agency recommendations. In addition, the matrix effect on MS response was measured on all investigated analytes spiked in urine samples. The limits of detection ranged from 1 to 500 ng/mL, allowing the identification of all tested compounds in urine. When a sample was reported positive during the screening, a fast additional pre-confirmatory step was performed to reduce the number of confirmatory analyses.

The influence of the organic content, sample preparation process and the morphology of the depositions of two types of Coke beverage, traditional and light Coke, have been investigated by mean of Total-reflection X-ray Fluorescence (TXRF) spectrometry. Strong distortions of the nominal concentration values, up to 128% for P, have been detected in the analysis of traditional Coke by different preparation methods. These differences have been correlated with the edge X-ray energies of the elements analyzed being more pronounced for the lighter elements. The influence of the organic content (mainly sugar) was evaluated comparing traditional and light Coke analytical TXRF results. Three sample preparation methods have been evaluated as follows: direct TXRF analysis of the sample only adding internal standard, TXRF analysis after open vessel acid digestion and TXRF analysis after high pressure and temperature microwave-assisted acid digestion. Strong correlations were detected between quantitative results, methods of preparation and energies of the X-ray absorption edges of quantified elements. In this way, a decay behavior for the concentration differences between preparation methods and the energies of the X-ray absorption edges of each element were observed. The observed behaviors were modeled with exponential decay functions obtaining R 2 correlation coefficients from 0.989 to 0.992. The strong absorption effect observed, and even possible matrix effect, can be explained by the inherent high organic content of the evaluated samples and also by the morphology and average thickness of the TXRF depositions observed. As main conclusion of this work, the analysis of light elements in samples with high organic content by TXRF, i.e. medical, biological, food or any other organic matrixes should be taken carefully. In any case, the direct analysis is not recommended and a previous microwave-assisted acid digestion, or similar, is mandatory, for the correct elemental quantification by TXRF.

Ambient mass spectrometry—mass spectrometric analysis with no or minimal effort for sample preparation—has experienced a very rapid development during the last 5 years, with many different methods now available for ionization. Here, we review its range of applications, the hurdles encountered for its quantitative use, and the proposed mechanisms for ion formation. Clearly, more effort needs to be put into investigation of matrix effects, into defining representative sampling of heterogeneous materials, and into understanding and controlling the underlying ionization mechanisms. Finally, we propose a concept to reduce the number of different acronyms describing very similar embodiments of ambient mass spectrometry.

An investigation on filtration procedures and SPE sorbents used for the determination of traces of the most common veterinary fluoroquinolones (FQs), marbofloxacin (MAR) and enrofloxacin (ENR) used as antibacterial agents in cattle and swine farms in the province of Pavia (Italy), was performed in natural waters. The filter composition and the sorbent used in the SPE strongly influence the correct recovery, both in terms of total and dissolved FQs concentration. An accurate comparison among different filters and SPE sorbents showed that a full determination of analytes was possible on nylon filters followed by anionic (WAX) and hydrophilic–lipophilic balance (HLB) resins as SPE. Quantitative analysis was done by chromatography with fluorescence detection (HPLC-FD). Fluoroquinolones recovery was between 90 and 116% with RSD not greater than 10% (sample volume 250 mL). The developed method allowed to determine both dissolved and NOM-absorbed fractions of FQs, therefore a full determination of the analytes was possible. Limits of detection (LOD) and quantification (LOQ) were, respectively, 0.7 and 2.2 ng/L for ENR and 2 and 6 ng/L for MAR. The kinetics of degradation under solar light was explored.

Background It is a general belief that a food allergen should be stable to gastric digestion. Various acidic plant polysaccharides, including pectin, are ubiquitous in fruit matrixes and can form hydrogels under low-pH conditions.Objective The purpose of this study was to investigate the effect of hydrogel forming polysaccharide-rich fruit matrixes on in vivo gastric and in vitro pepsic digestion of fruit allergens.Methods Fruit extract proteins (kiwi, banana, apple and cherry) and a purified major kiwi allergen Act c 2 were digested with simulated gastric fluid in accordance with the US Pharmacopeia. In vivo experiments on kiwi fruit digestion were performed on four healthy non-atopic volunteers by examining the gastric content 1 h after ingestion of kiwi fruit. The Act c 2 and kiwi proteins were detected in immunoblots using monoclonal anti-Act c 2 antibodies and rabbit polyclonal antisera.Results Crude fruit extracts were resistant to digestion by pepsin when compared with commonly prepared extracts. In the gastric content of all volunteers, following kiwi fruit ingestion and immunoblotting, intact Act c 2 was detected with anti-Act c 2 monoclonal antibodies, while kiwi proteins of higher molecular weights were detected using rabbit polyclonal antisera. Addition of apple fruit pectin (1.5% and 3%) to the purified kiwi allergen was able to protect it from pepsin digestion in vitro.Conclusion The matrix effect in pectin-rich fruits can influence the digestibility of food proteins and thereby the process of allergic sensitization in atopic individuals.

This paper describes an improved method for the extraction and analysis of seven endocrine disrupting chemicals with wide-ranging polarities from water and sediments using gas chromatography-tandem mass spectrometry (GC-MS/MS). The analytes were 4-tert-octylphenol, 4-nonylphenol, bisphenol A, estrone, 17beta-estradiol, 17alpha-ethynylestradiol and 16alpha-hydroxyestrone. The optimised GC-MS/MS method produces increased selectivity and sensitivity compared to GC-MS, with limit of detection ranging from 0.01 to 0.49 ng L(-1) in water and from 0.05 to 0.14 ng g(-1) in sediment. Extraction from aqueous samples was performed by solid-phase extraction (SPE) and from sediment samples by microwave-assisted extraction (MAE). The improved method for the clean-up of sediment extracts carried out by SPE enhanced EDC recovery (86-102%) while reducing matrix interference and sample drying time. Derivatisation of final sample extracts was achieved using N,O-bis(trimethylsilyl)trifluoroacetamide an...